Archive for the ‘commercial pressure washers’ Category

AR – ANNOVI REVERBERI RSV4G40H-F40 Pump   Leave a comment


AR – ANNOVI REVERBERI RSV4G40H-F40 4GPM 4000PSI 1″ GAS

The AR – Annovi Reverberi RSV4G40H-F40,

Features

  • MANIFOLD: NEW high efficiency design concept. Patented forged brass for strength and no porposity for long life and higher hydrostatic pressures
  • BOLTS: Eight 6mm grade 8.8
  • PLUNGERS: Ceramic coated stainless steel
  • CRANKCASE: Precision die-cast cooling fins and anodized for maximum heat dissipation
  • BEARINGS: Oversized for maximum life and load disbursement, needle bearing on the drive side and ball on the non drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. this assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankcase from floating
  • VALVES, SEATS AND SPRINGS: Stainless steel with specially designed ultra form cages to provide long life and positive seating
  • SEALS AND V-PACKINGS: “V” style (D-1) buna-N strong and tightens under load
  • OIL SEALS: All are constructed of Buna-N riubber
  • PLUNGER RODS: Stainless steel construction for strength (no plating to scrape off) o-ring plunger sealing system
  • CONNECTING RODS: One piece special alloy aluminum and bronze based, oversized for maximum strength, load disbursement, and life. Heavy pin area construction for added load strength

Specifications for the AR – Annovi Reverberi RSV4G40H-F40,

  • 1″ gas flange hollow shaft
  • Built-in adjustable unloader
  • Maximum flow: 4.0 GPM 15.1 LPM
  • Maximum Pressure: 4000 PSI 275 BAR
  • Minimum Horsepower: 15 Gas
  • Maximum temperature: 140F
  • Plunger: 15mm
  • Oil Capacity: 16 oz
  • Inlet thread: 1/2″ FPT
  • Discharge thread: 3/8″ FPT
  • Weight: 14 lbs.

List Price: $518.28

Our Price: $398.82

CLICK TO ORDER the AR – Annovi Reverberi RSV4G40H-F40

You save $119.46!

General Pump TS 1011   Leave a comment


GENERAL PUMP,T SERIES 47 TS1011

  • The preferred pump frame in the cleaning industry
  • Forged brass manifold with an exdlusive lifetime warranty
  • Large capacity, die cast, anodized aluminum oil bath crankcase
  • Over sized connecting rods for maximum life
  • Heavy duty tapered roller bearing
  • Solid ceramic plungers with continuously lubricating packings
  • Unitized stainless steel inlet and discharge valves
  • Available in left handed “L” version
  • Triplex Plunger Pump
  • Maximum Volume: 4.0/4.75 GPM
  • Maximum Discharge Pressure: 2000/1500 PSI
  • Maximum Inlet Pressure: 125 PSI
  • Maximum Pump Speed: 1450/1750 RPM
  • Minimum Horsepower Requirements: 5.5 bhp (8.2 hp for gas engines)
  • Bore: .787″ (20mm)
  • Stroke: .472″ (12mm)
  • Crankcase Capacity: 33.8 oz. Nondetergent SAE 30W oil
  • Maximum Fluid Temperature: 165 degrees F.
  • Inlet Port thread: 1/2″ FPT
  • Discharge Port Thread: 3/8″ FPT
  • Shaft Diameter: .945″ (24mm)
  • Dimensions: 11.4″ x 9.2″ x 6.9″
  • Weight: 30 lb.
  • Lubrication: Fill the crankcase to the dot on the oil gauge window pe specifications with SAE 30W oil. Change the oil after a 40 hour break in period, then every three (3) months or 500 hour intervals thereafter.

Need parts for this pump? Click here for the datasheet.

List Price: $717.08

Our Price: $551.79

You save $165.29!

CLICK TO PURCHASE HERE…

 

Hypro Car Wash Plunger Pump 2535S   Leave a comment


HYPRO CAR WASH PLUNGER PUMP

The Hypro 2535S triplex plunger pump is designed for durability, top performance, and convenient servicing. It achieves up to 38 gpm (144 lpm) and 1200 psi (83 bar). The 316 stainless steel two-piece manifold minimizes washout and corrosion. A strong power end including oversized crankshaft, bearings, and connecting rods easily handles abuse caused by start-up and intermittent operation. Backed by the best warranty in the industry, Hypro pumps are designed for, and not adapted to, the car wash industry, resulting in pumps that deliver higher pressure and increased reliability.

  • 38GPM
  • 1200 Max PSI
  • 800 Max RPM
  • oil bath crankcase
  • ceramic plungers
  • 35mm OD solid shaft
  • 1 1/2″ NPT inlet port
  • 1″ NPT outlet port

List Price: $6,424.00

Our Price: $4,108.03

You save $2,315.97!

CLICK HERE TO PURCHASE

General Pump – Electric Pressure Washers   Leave a comment


General Pump Complete Electric Pressure Washers 

 

Photo(Where available) Part Name/Number Description

FOR99SM

FORMULA 99 – Turbo 21 pressure Washer, aluminum manifold

190118

QUIKY – Turbo 21 pressure washer,

brass manifold

PU1021

BOXJET – aluminum manifold

PU1021B

BOXJET – brass manifold

PU1021QB

QUIKY, brass manifold

CLEANMATIC

Pressure Washer

General Pump Electric Pressure Washer Accessories

 

 

 

Photo(Where available) Part Name/Number Description

No Photo

Z0BOXCART

Cart kit for Boxjet

No Photo

Z0BOXWALL

Wall Brackets for Boxjet

No Photo

Z0BRUSHKIT

Boxjet rotating brush kit

Z0SANDKIT1

Boxjet sandblasting kit

No Photo

100200

Universal cart for pressure washer

 

General Pump High Flow / High Pressure Pumps   Leave a comment


General Pump 66 Series High Flow The General Pump 66 Series High Flow pumps are versatile and feature a new triplex design that extends seal life! GPM ranges from 6.3 to 12.0 and pressures from 2500 to 3600 psi.  

 

Photo(Where available) Parts List Description

Triplex pump

TSF2021 (new pump price)

Triplex pump

TSF2219 (new pump price)

Triplex pump

TSF2221 (new pump price)

Triplex pump

TSF2421 (new pump price)

Triplex pump

General Pump 66 Series High Pressure The 66 Series General Pumps provide a COMPACT high pressure design providing from 4.3 to 5.5 gpm and from 5000 up to 5800 psi. 

 

Photo(Where available) Part Name/Number Description

TSP1621

High pressure triplex pump

TSP1819

High pressure triplex pump

 

General Pump T Series 69 The T Series 69 High-Flow general pumps offer a large crankcase that produces 8.0 to 12.0 gpm at low pressure. 

 

Photo(Where available) Part Name/Number Description

T41

Triplex plunger pump, 36mm bore

TS1041

Triplex plunger pump, 20mm bore

TS1531

Triplex plunger pump, 20mm bore

 

General Pump T Series 76 The T Series 76 General Triplex Plunger Pumps are the High Flow Industries choice! Lifetime warranty on manifold! From 6.6 gpm to 21 gpm & 1000 to 5800 psi max. 

 

Photo(Where available) Part Name/Number Description

T1551

Triplex plunger pump, 30mm bore

T4251

Triplex plunger pump, 20mm bore

T61

Triplex plunger pump, 45mm bore

T81

Triplex plunger pump, 45mm bore

 

General Pump T Series 48 The T Series 48 General Pumps are great for High-Flow / High Pressure Applications with its dual mainfold a.k.a, sixplex a.k.a. multiplex design, 9 to 11 gpm – high pressure, 2-3000 psi. 

 

Photo(Where available) Part Name/Number Description

T1631

Sixplex plunger pump

T2031

Sixplex plunger pump

TS1351

Sixplex plunger pump

 

General Pump T Series 77 The T Series 77 General Pumps are designed for High-Flow & High Pressure Applications – 25 gpm+ 

 

Photo(Where available) Part Name/Number Description

T121

Sixplex plunger pump, 45mm bore

T151

Sixplex plunger pump, 45mm bore

T1591

Sixplex plunger pump, 30mm bore

T3551

Sixplex plunger pump, 20mm bore

 

General Pump AT Series 75 AT Series 75 General pumps are ideal for grain cleaning and jetting applications with its dual pulsing action, 7.93 gpm up to 22.48 max gpm – low pressure. 

 

Photo(Where available) Part Name/Number Description

AT0033

Duplex plunger pump, splined shaft

AT0055

Triplex plunger pump, splined shaft

AT0088

Triplex plunger pump, splined shaft

 

General Pump AT Series 77 The AT Series 77 General Pumps are great for High-Flow applications with its dual manifold a.k.a, sixplex a.k.a. multiplex design, 29.1 to 45 gpm – low pressure. 

 

Photo(Where available) Part Name/Number Description

No Photo

AT0111

Sixplex plunger pump, splined shaft

No Photo

AT0177

Sixplex plunger pump, splined shaft

No Photo

AT0177B

Sixplex plunger pump, splined shaft

 

 

GIANT Pumps, Parts & Kits   Leave a comment


GIANT CONSUMER PUMPS
GIANT GXR Vertical or Horizontal Pumps with Regulator includes Siphon Injector, Thermal Relief Valve and Engine Mounting Accessories
Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End
GXR 2424 2.4 2400 3450 5.2 Brass
GXR 2224 2.2 2400 3450 5.0 Brass

Weight: 9 lbs. Bore Size: 3/4″ Horizontal, 7/8″ Vertical Max. Temperature: 80 degree F

Inlet Port: 1/2″ NPT Discharge Port: 3/8″ NPT

GIANT GX Vertical or Horizontal Pumps with Unloader includes Siphon Injector, Thermal Relief Valve and Engine Mounting Accessories GX2525
Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End
2.0
2500
3450
3.4
Brass
2.3
2500
3450
3.9
Brass
GX 2525 2.5 2500 3450 4.3 Brass

Weight: 9 lbs. Bore Size: 3/4″ Horizontal, 7/8″ Vertical Max. Temperature: 80 degree F

Inlet Port: 1/2″ NPT Discharge Port: 3/8″ NPT

GIANT P200 PUMPS

Series Triplex Plunger Pumps

P200 Pump Assemblies
P200 Belt Drive P200 Electric Drive
GIANT BELT DRIVE Pump
GIANT ELECTRIC DRIVE Pump
P200 Gas Drive
GIANT GAS DRIVE Pump

GIANT P200 Pump Assemblies

Model Max. GPM PSI Continuous PSI Intermittent Max. RPM Req’d BHP Fluid End
P205 0.5 2000 2500 1750 1.2 Brass
P206 0.8 2000 2500 1750 2.1 Brass
P205 0.9 2000 2500 3450 1.2 Brass
P208 1.0 2000 2500 1750 2.6 Brass
P230 1.1 2000 2500 1750 2.8 Brass
P209 1.5 2000 2500 1750 6.2 Brass
P206 1.5 2000 2500 3450 1.8 Brass
P223 1.7 2000 3000 1750 4.6 Brass
P210 1.8 2000 2500 1750 2.6 Brass
P217 1.8 2000 2500 1750 2.8 Brass
P208 1.9 2000 2500 3450 2.6 Brass
P230 2.0 2000 2500 3450 2.8 Brass
P221 2.3 2000 2500 1750 2.8 Brass
P209 2.7 2000 2500 3450 3.7 Brass
P223 3.0 2000 3000 3450 6.2 Brass
P217 3.3 2000 2500 3450 4.6 Brass
P210 3.3 2000 2500 3450 4.6 Brass
P218 3.4 2000 2500 1750 4.7 Brass
P219 4.2 2000 2500 1750 4.7 Brass
P221 4.2 2000 3450 5.8 Brass
P220 4.7 2000 2500 1750 6.5 Brass
GIANT P300 PUMPS

Series Triplex Plunger Pumps

GIANT P300 ASSEMBLIES
P300 Electric Drive P300 Gas Drive
GIANT P300 Series Pump with Electric Drive
GIANT P300 Series Pump with Gas Drive
P300 Belt Drive P300 Gas Drive 2
GIANT P300 Series Pump
GIANT P300 Series Pump with Gearbox

GIANT P300 SERIES PUMPS

Model GPM Cont. PSI Cont.
PSI Inter.
Max. RPM Req’d BHP Fluid End
P340 3.5 3500 4000 1750 8.4 Brass
P317 3.7 3000 3500 1800 7.7 Brass
P313 3.8 3200 3500 3450 8.4 Brass
P314 3.8 3500 4000 3450 9.2 Brass
P316 3.9 3000 3500 1450 8.1 Brass
P316 4.7 2500 3000 1750 8.1 Brass
P319 4.8 2500 3000 3400 8.3 Brass
P318 5.5 2000 1450 7.6 Brass
P318 6.6 2000 1750 7.6 Brass
GIANT 400 Series Triplex Plunger Pumps

P460
Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Notes
3.8
7250
1450
19.0
S.S.
5.5
5000
1450
19.0
Brass
5.5
3200
1450
19.0
Al.Bronze
7.5
3200
1450
14.8
Brass
5.5
4000
1450
15.2
Al.Bronze
8.3
2600
1450
14.9
Brass
10.0
2500
1450
20.7
Brass
10.7
2000
1450
15.6
Brass
13.0
1700
1460
15.2
Brass
13.0
1700
1460
15.2
Al.Bronze
13.0
2000
1460
15.2
316 S.S.

Weight: 37 lbs. Shaft Size: 28mm Max. Temperature: 160 oF (104 oF for P460) * Consult factory when operating at this speed.

Port sizes:

Pump Model Inlet Port Discharge Port
P420A/P422 (2) 1 ” NPT (2) 3/4″ NPT
P440 (2) 3/4″ NPT (2) 3/4″ NPT
P430 (2) 3/4″ BSP (2) 3/4″ BSP
P450A (2) 1/2″ BSP (2) 1/2″ BSP
P420-3100/P420-5100 (2) 1″ BSP (2) 3/4″ BSP
P460 (2) 1/2″ BSP (2) 1/2 ” BSP
GIANT Bentonite PumpsGiant Industries Bentonite pumps, are used for transporting of the Bentonite fluid used in the stabilization of bore holes in horizontal boring applications. These pumps range from up to 18.5 GPM – 84.5 GPM and up to 1500 PSI. All of these pumps are made of cast Iron fluid ends with solid ceramic plungers provide long life. And the gear end construction of heavy-duty cast iron crankcase, glazed, hardened and ground crankshaft and aluminum-bronze bearings provide years of life. With a seal life of 300-400 hours you can expect Performance Under Pressure with Giant.

BP5236

Volume:………………………………………Up to 18.5 GPM
Discharge Pressure:………………………….Up to 900 PSI
Speed:…………………………………………Up to 570 RPM
Inlet Pressure:…………………………………-4.35*-150PSI
Power Consumption:…………………………………..12 HP
Plunger Diameter:………………………………………36mm
Plunger Stroke:…………………………………………42mm
Crankshaft Diameter:………………………………….35mm
Key Width: ……………………………………………….8mm
Shaft Rotation:……………Top of pulley towards manifold
Temperature of Pumped Fluids: ……………Up to 104°F
Inlet Ports:……………………………………..(2) 1-1/2″ NPT
Discharge Ports:…………………………………..(2) 1″ NPT
Weight:………………………………………………….120 lbs.
Crankcase Oil Capacity:…………………………..116 fl.oz.
Fluid End Material:………………………………….Cast Iron
BP5236

BP6150

Volume:……………………………………..Up to 42.3 GPM
Discharge Pressure:……………………….Up to 1500 PSI
Speed:………………………………………..Up to 600 RPM
Inlet Pressure:……………………………….-4.35* -150PSI
Power Consumption:………………………………..43.8 HP
Plunger Diameter:……………………………………..50mm
Plunger Stroke:………………………………………..48mm
Crankshaft Diameter:…………………………………45mm
Key Width: …………………………………………….12mm
Crankshaft Mounting:…………………………..Either side
Temperature of Pumped Fluids: …………..Up to 104 oF
Inlet Ports:…………………………………….(2) 2-1/2″ NPT
Discharge Ports:…………………………….(2) 1-1/4″ NPT
Weight:……………………………………………..275.5 lbs.
Crankcase Oil Capacity:…………………………..1.1 Gal.
Fluid End Material:………………………………..Cast Iron
BP6150

BP7170

Volume:………………………………………Up to 84.5 GPM
Discharge Pressure:……………………….Up to 1015 PSI
Speed:………………………………………..Up to 560 RPM
Inlet Pressure:………………………………..-4.35* -150PSI
Power Consumption:…………………………………..59 HP
Plunger Diameter:………………………………………70mm
Plunger Stroke:…………………………………………52mm
Crankshaft Diameter:………………………………….48mm
Key Width: ………………………………………………14mm
Crankshaft Mounting:…………………………….Either side
Temperature of Pumped Fluids: ……………Up to 104 oF
Inlet Ports:……………………………………..(2) 2-1/2″ NPT
Discharge Ports:……………………………..(2) 1-1/4″ NPT
Weight:………………………………………………….423 lbs.
Crankcase Oil Capacity:…………………………….1.1 Gal.
Fluid End Material:………………………………….Cast Iron
BP7170
GIANT Light Industrial Pumps

Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End
1.8
2000
3450
3.3
Brass
HR2527 2.5 2700 3450 4.6 Brass
HR3025 3.0 2500 3450 6.8 Brass
HR3030 3.0 3000 3450 6.2 Brass

Weight: 9 lbs. Bore Size: 3/4″ for HR2527, 1″ for HR3030 Max. Temperature: 80 degree F Inlet Port: 1/2″ NPT Discharge Port: 3/8″ NPT
GIANT HIGH TEMPERATURE PUMPS

Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Shaft (mm)
P46HT 2.1 900 750 1.3 Brass 18
P46W-HK+ 4.5 1700 1655 5.3 Brass 18
P56HT 3.2 900 750 2.0 Brass 22
P56W-HK+ 7.1 2500 1655 10.2 Brass 22
MP4130HT 10.5 1200 750 8.6 Al. Bronze 28
MP4130HTC* 10.5 1200 750 8.6 Al. Bronze 28
LP121HT 17.6 1200 570 14.6 Al. Bronze 35
LP121HTC* 17.6 1200 570 14.6 Al. Bronze 35

Max. Temperature: 220 oF + Max. Temperature: 190 oF * HTC = Pumps with coolant connection

GIANT CORROSION RESISTANT PUMPS

Aluminum Bronze Manifolds & 316 Stainless Steel Internal Wet End Parts

Model Max. GPM Max. PSI Max. RPM Req’d BHP Weight (lbs) Shaft (mm)
P221AR-3100 2.3 2000 1750 3.2 12 24
P217A-3100 3.4 2000 3450 4.7 12 24
P218A-3100 3.4 2000 1750 4.7 12 24
P219A-3100 4.2 2000 1750 5.8 12 24
P220A-3100 4.7 2000 1750 6.4 12 24
P230A-3100 1.1 2000 1750 2.8 12 24
P420A-3100 13.0 1700 1460 15.2 37 28
P430A-3100 5.5 5000 1460 19.0 37 28
MP4130-3100 15.2 1900 1085 20.0 72 28
LP122A-3100 39.0 1300 885 34.5 116 32
GP6145A-3100 46.2 1740 800 55.8 309 42
GP7155A-3100 66.0 1500 700 70.5 455 48

316 Stainless Steel Manifolds and Internal Wet End Parts

Model Max. GPM Max. PSI Max. RPM Req’d BHP Weight (lbs) Shaft (mm)
2.3
2000
1750
3.2
12
24
P217A-5100 3.4 2000 3450 4.7 12 24
P218A-5100 3.4 2000 1750 4.7 12 24
P218A-5100E 3.4 2000 1750 4.7 12 24
P219A-5100 4.2 2000 1750 5.8 12 24
P219A-5100E 4.2 2000 1750 5.8 12 24
P220A-5100 4.7 2000 1750 6.4 12 24
P220A-5100E 4.7 2000 1750 6.4 12 24
P56-5100 7.1 2100 1655 10.2 22 18
P420A-5100 13.0 1700 1460 15.2 37 28
LP121A-5100 36.0 1300 885 32.1 116 35
GP5145-5100 43.3 1500 750 44.8 179 35
GP7155-5100 66.0 1500 700 70.5 455 48
P230A-5100 1.1 2000 1750 2.8 12 24
P55-5100 4.9 2320 1420 7.8 18 24
P450-5100 5.5 5000 1450 19 37 28
P422-5100 10 2200 1450 15.2 37 28
LP301A-5100 14.2 4000 1000 39.2 119 35
LP600-5100 9.8 6000 1000 40.6 119 35
LP250A-5100 26 2200 1000 39.4 119 35
GP5136-5100 33.8 2300 910 53.6 179 35
GP7142-5100 38.4 2600 700 68.9 374 52
GIANT CO2 Pumps

CP205, CP218, CP220
CP205
Flow:…………………………………Up to 0.21 GPM
PSI:…………………………………….2000/2500 PSI
RPM:……………………………………………….1750
Inlet Ports: ……………………………..(2) 1/2″ BSP
Discharge Ports: ………………………(2) 3/8″ BSP
Temp. of pumped fluids:……………………….-40oF
Weight:…………………………………..11 lbs. 11oz
CP218
Flow:…………………………………..Up to 1.4 GPM
PSI:……………………………………………2030 PSI
RPM:…………………………………………………750
Inlet Ports:……………………………….(2) 1/2″ BSP
Discharge Ports:……………………….(2) 3/8″ BSP
Temp. of pumped fluids:……………………….-40oF
Weight:……………………………………11 lbs. 11oz.
CP220
Flow:…………………………………Up to 1.93 GPM
PSI:……………………………………………2030 PSI
RPM:…………………………………………………750
Inlet Ports: ……………………………..(2) 1/2″ BSP
Discharge Ports: ………………………(2) 3/8″ BSP
Temp. of pumped fluids:……………………….-40oF
Weight:…………………………………..11 lbs. 11oz.
CP420 CP7155
CP420
Flow:…………………………………Up to 6.4 GPM
PSI:…………………………………………..1810 PSI
RPM:…………………………………………………750
Inlet Ports: ……………………………..(2) 3/4″ NPT
Discharge Ports: ………………………(2) 3/4″ NPT
Temp. of pumped fluids:……………………….-40oF
Weight:…………………………………..11 lbs. 11oz
CGP7155
Flow:…………………………………Up to 51.5 GPM
PSI:……………………………………………1450 PSI
RPM:………………………………….Up to 550 RPM
Inlet Ports:…………………………….(2) 2-1/2″ NPT
Discharge Ports:……………………..(2) 1-1/4″ NPT
Temp. of pumped fluids:……………………….-40oF
Weight:………………………………………….455 lbs
CLP200
Flow:…………………………………Up to 9.5 GPM
PSI:…………………………………………..1750 PSI
RPM:………………………………………………..500
Inlet Ports: ………………………..(2) 2X1-1/4″ BSP
Discharge Ports: …………………….(2) 2X1 ” BSP
Temp. of pumped fluids:……………………….-40oF
Weight:………………………………….. 119 lbs.
CLP121A
Flow:…………………………………Up to 16.3 GPM
PSI:……………………………………………1740 PSI
RPM:…………………………………. 500 RPM
Inlet Ports:…………………………….(2) 1-1/4″ BSP
Discharge Ports:……………………. (2) 1-1/4″ BSP
Temp. of pumped fluids:……………………….-40oF
Weight:………………………………………….119 lbs

GIANT Industrial Triplex Plunger Pumps

P46/P55/P56 Pumps

Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Notes
P57 1.4 6500 1420 6.0 S.S.
P46 3.9 2200 1420 5.3 Brass
P55 6.0 2320 1750 10.2 Brass
P56 7.5 2200 1750 10.2 Brass
P56-5100 7.1 2100 1655 10.2 316 S.S. Standard Seals
P56-5111 7.1 2100 1655 10.2 316 S.S. Viton Seals
P56-5121 7.1 2100 1655 10.2 316 S.S. Teflon/Viton Seals

* Includes Pump, Unloader, Pop-off valves, Two Guns, Pressure Switch, Thermal Relief Valve Weight: 18 lbs. Shaft Size: 18mm for P46W, 22mm for P55, P56, P56-5100, P57, 24mm for P54, P58, P59 Max. Temperature: 160 degree F

P54/P58/P59 Pumps

Pump Model Max. GPM PSI Continuous PSI Intermittent Max. RPM Req’d BHP Fluid End
P54 4.8 4000 3300 1750 11.0 Brass
P54GB 4.8 4000 3300 1750 11.0 Brass
P58 6.0 3500 3000 1750 12.1 Brass
P58GB 6.0 3500 3000 1750 12.1 Brass
P59 9.0 1900 1000 1750 10.0 Brass
P59GB 9.0 1900 1000 3500 10.0 Brass
P59DG* 9.0 1900 1000 3500 10.0 Brass

Inlet Port & Discharge Port:

Pump Model Inlet Port Discharge Port
P46/P55/P56/P56-5100/P56-5100/P57 (2) 1/2″ BSP (2) 3/8″ BSP
P54/P58/P59 (2) 3/8″ BSP & (1) 1/2″ BSP (2) 3/8″ BSP

GIANT SP Pumps

Pump Model Max. GPM Max. PSI Max. RPM BHP Max. Temp. F
SP100W 11.2 2000 1420 14.5 160° F
6.7
3200
1420
14.8
160° F

Weight: 30 lbs. Shaft Size: 28mm Max. Temperature: 160 degree F Inlet Port: (2) 3/4″ NPT Discharge Port: (2) 3/8 ” NPT

GIANT MP Series Pumps

Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Note
MP4120W 8.7 3600 1420 21.8 Al. Bronze
MP4124W 12.6 3000 1420 21.0 Al. Bronze
MP4130 15.2 1900 1085 20.0 Al. Bronze

Weight: 72 lbs. Shaft size: 28 mm Max. Temperature: 160 oF

Port sizes:

Pump Model Inlet Port Discharge Port
All (2) 1” NPT (2) 3/4″ NPT

GIANT LP Series Pumps

LP301 LP1000 LP700
LP301 LP1000 LP700

Giant LP Series – High Pressure

Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Note
LP1000 3.4 15000 1000 35.2 S.S
LP700 7.9 7250 1000 39.8 S.S
LP600 9.7 6000 1000 40.4 S.S
LP301A 14.1 4000 1000 50.0 S.S
LP400 15.1 3600 1000 37.6 Al. Bronze
LP301A* 18 4000 1270 49.7 S.S
LP200 19.0 2900 1000 38.4 Al. Bronze
LP450 19.7 2600 1000 35.5 Al. Bronze
LP350 22.6 2350 1000 36.1 Al. Bronze

GIANT LP Series – High Flow

Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Note
LP250 26.0 2200 1000 39.7 Al. Bronze
LP255 26.0 2200 1000 39.7 Brass
LP122A 39.0 2000 885 56.3 Al. Bronze
LP123 39.0 2000 885 56.3 Brass

* Intermittent duty only

Weight: 116 lbs. Shaft Size: 35mm

Max. Temperature: 140 degree F (104 F for LP1000)

Inlet Port & Discharge Port:

Pump Model Inlet Port Discharge Port
LP200/LP301A/LP600 (3) 1-1/4″ BSP (2) 1″ BSP
LP350/LP400/LP450 (2) 1-1/4″ BSP (1) 1″ BSP
LP700 (2) 3/4″ NPT (2) 1/2″ NPT
LP1000 (3) 1/2″ BSP (2) 3/8″ BSP
LP122/LP122A-4000/LP123 (2) 1-1/2″ NPT (2) 1″ NPT
LP250/LP255 (3) 1-1/2″ BSP (3) 1″ BSP

GIANT GP Series Pumps

GP7124A GP7255A
GP7124A GP7255A

GIANT GP Series – High Pressure

Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Notes
GP7122 9.9 10150 750 69.3 S.S
GP7124A 12.7 7250 750 65.7 S.S
GP6124 12.8 5800 800 53.1 S.S
GP6128 18.0 4000 800 51.0 S.S
GP7132 23.4 4350 750 73.0 S.S
GP7136 28.3 3650 750 73.0 S.S
GP5132 27.7 2900 1000 60.0 Cast Iron
GP51 weight: 179 lbs Shaft Size: 35mm Max. Temperature: 140 oF
GP61 weight: 309 lbs Shaft Size: 42mm Max. Temperature: 140 oF
GP71 weight: 374 lbs Shaft Size: 48mm Max. Temperature: 140 oF

GP Series – High Flow

Pump Model Max. GPM Max. PSI Max. RPM Req’d BHP Fluid End Note
GP5136 33.8 2300 960 53.1 Cast Iron
GP5145 43.5 1500 750 44.8 Cast Iron
GP7150A 54.5 1900 700 74.0 Al. Bronze
GP7155 65.8 2000 700 55.3 Al. Bronze
GP7255A 66.0 2000 700 94.3 Cast Iron
GP51 weight: 179 lbs Shaft Size: 35mm Max. Temperature: 140 oF
GP61 weight: 309 lbs Shaft Size: 42mm Max. Temperature: 140 oF
GP71 weight: 374 lbs Shaft Size: 48mm Max. Temperature: 140 oF

Inlet Port & Discharge Port:

Pump Model Inlet Port Discharge Port
GP5132/GP5136/GP5145 (2) 1-1/2″ BSP (2) 1″ BSP
GP6124/GP6124-4000/GP6128 (2) 1-1/2″ BSP (2) 1″ BSP
GP6132/GP6140/GP6145/GP6145-4000 (2) 2-1/2″ NPT (2) 1-1/4″ NPT
GP7122 (2) 1-1/4″ BSP (2) 3/4 ” BSP
GP7124A/GP7128/GP7132 (2) 1-1/4″ NPT (2) 3/4″ NPT
GP7136 (2) 1″ NPT (2) 1-1/4″ NPT

Hypro Pumps, New and Replacement Pressure Washer Pumps   Leave a comment


HYPRO Piston Pump Replacements

Hypro Corporation’s Twin® piston and plunger pumps are used in a variety of spraying and pressure cleaning applications, as well as hydrostatic testing. These heavy-duty pumps are ideal for fluid handling of water and nonabrasive or general use chemicals. All pumps are constructed from cast iron materials. They feature stainless steel valves and ball bearing, leather or fabric-reinforced Buna-N or straight Buna-N cups. You can choose from a variety of drive systems to include: belt and pulley, 540 rpm PTO, gasoline engine or electric motor. These pumps are available in a variety of flow and pressure ranges up to a maximum of 10 gpm and 1000 psi, with maximum fluid temperatures of 140°F (piston pumps) and 180°F (plunger pumps).

All of the Hypro piston and plunger pumps share these quality features:

• Nonabrasive and general use chemical compatibility

• Compact, lightweight and easy to install

• Replaceable leather cups for insecticides, herbicides and aromatic solvents

• Replaceable Buna-N and fabric reinforced Buna-N cups for water, soap and detergent solutions

• They are bi-rotational

• Self priming operation (piston pumps)

See Piston Pump Catalog here for detailed pump information

PISTON PUMPS

*This requires a “special order” gas engine with a 5/8″ shaft.

See Piston Pump Catalog here for detailed pump information

See Hypro Plunger Pump brochure for detailed Plunger Pump information

( See also Hypro Industrial Plunger Pump Brochure )

PLUNGER PUMPS
PowerLine PLUS 2200B-P Duplex Plunger Pumps
PowerLine PLUS 2300B-P Triplex Plunger Pumps
PowerLine PLUS 2400B-P and 2430B-P Triplex Plunger Pumps with Gearbox
2401B-P
2345B-CP
2200B-PU3
2431B-G2P
2433B-G2P
2231B-HPU3

See Hypro Plunger Pump brochure for detailed Plunger Pump information

( See also Hypro Industrial Plunger Pump Brochure )

Agricultural ROLLER Pump Models available:

Hypro roller pumps are designed for agricultural and industrial spraying and transfer of a variety fluids. These include insecticides, herbicides, emulsives, aromatic solvents, liquid fertilizers and many other liquids. The economical rotary-action roller principle requires no check valves while providing positive displacement characteristics with less friction and lower starting torque than other pumps. Construction features include a cast-iron, Ni-Resist or the new SilverCast™ body and rotor, 416 stainless steel shaft, sealed factory-lubricated ball bearings, cartridge-type lip seals of Viton, Buna-N or leather, and versatile Super Rollers. (Super Rollers feature the life of polypropylene and the chemical resistance of nylon.) Rotation for all models is counterclockwise for easy tractor PTO drive, except models 4001 and 4101 which are clockwise. Pumps are available in reverse rotation.

See Hypro Roller Pump Brochure for detailed Roller Pump information

*Cast iron and XL versions are available. Call us Toll Free 1-877-824-7763 for details.

See Hypro Roller Pump Brochure for detailed Roller Pump information

New HYPRO Diaphragm Pumps

Diaphragm pumps are the most complete line of pumps available for spraying and pumping of herbicides, pesticides, liquid fertilizers and hard-to-handle fluids! Hypro offers a wide range of flows and pressures for slurries and suspensions. Pressures for row crop to treetop spraying applications range from 20 to 725 psi (1.4 to 50 bar) with flow rates from 3.5 to 66 gpm (13.2 to 249.8 lpm).
Low-cost maintenance and almost wear-free operation result from Hypro’s oil-bath design, premium quality, synthetic diaphragms for longer life, self-priming operation and visual, oil-level sight glass. These models can handle fluids up to 140°F (60°C) and can be run dry. Hypro diaphragm pumps can be driven by 540 rpm PTOs, 3 to 25 hp gasoline engines, or hydraulic motors.

HYPRO Low Pressure Diaphragm Pumps

Low Pressure

HYPRO Medium Pressure Diaphragm Pumps

Medium Pressure

HYPRO High Pressure Diaphragm Pumps

High Pressure